Last trip memory |
Post Reply |
Author | |
Jgs101
Newbie Joined: 04 May 2019 Location: Kvny Status: Offline Points: 2 |
Post Options
Thanks(0)
Posted: 04 May 2019 at 3:57pm |
I was thinking how nice it would be if the 540 remembered the last flight-plan after startup, without having to save it or enter the reverse route. Just tap on a reverse route button and off you go.
|
|
SB Jim
Senior Member Joined: 30 Aug 2012 Status: Offline Points: 204 |
Post Options
Thanks(0)
|
Agreed.
If I’m doing a long cross country with a fuel stop I try to load the next leg while taxiing to the fuel depot but it will be gone after restart. It’s handy to have.
|
|
Gring
Senior Member Joined: 30 Dec 2011 Location: Kingston, NY Status: Offline Points: 724 |
Post Options
Thanks(0)
|
just save your flight plan as a route and then reload it upon startup. I’ll also add that it is not good practice to be “eyes inside” while taxiing.
Edited by Gring - 31 Jul 2019 at 6:11am |
|
Bob H
Senior Member Joined: 26 Jan 2018 Location: NH - KMHT Status: Offline Points: 290 |
Post Options
Thanks(0)
|
This was discussed under "Suggestions for 10.3". What percentage of the time will your next flight be a reverse of the previous flight, especially IFR? Entering a flight plan while taxiing in is no different than entering a flight plan while taxiing out. The "Route Function" does a great job of remembering flight plans and they are simple to load. In most cases, I think this capability would be an annoyance - having to clear out what is there before entering your next flight. Below are my comments from the other thread. Not all apply to this context but some certainly do.
In regard to remembering the last leg upon startup, I prefer to start with a clean slate. Things can change between shutdown and startup on how I’m going to fly. A clean slate has me be very deliberate about my route right before takeoff. The primary function of the IFD is to support IFR flight plans, this is a VFR point to point request, which I think will actually hinder IFR operations. Some things to consider: · Most of the time, I’m not sure what my next route or waypoint will be upon shutdown, so this feature will rarely come into play. Also, after shutdown or before the next flight, I can always put waypoints into the IFD100 for auto loading when connected to the panel IFD. · When flying IFR, upon shutdown, the IFD will retain the last route flown. Then on startup, I no longer have the option of just entering a route on the FPL page. I will either need to delete the old waypoints while entering the new, or I will be relegated to entering everything new in the ROUTE page. It limits my options and will cause extra work. · Upon startup now, I can do a database update in less time than it takes to warm up, taxi, and run-up. Loading a single VFR waypoint would be simpler and faster than that. I think you will find no extended run-up is necessary. I am left to conclude that for most IFR operations, this feature request would be a hindrance. Also, it will only come into play when the next VFR flight and waypoint are known, which is probably not very often (at least for me). Even then, the IFD 100 will certainly suffice. Edited by Bob H - 06 Aug 2019 at 9:56pm |
|
Bob
|
|
tony
Senior Member Joined: 06 Dec 2011 Location: Atlanta Status: Offline Points: 466 |
Post Options
Thanks(0)
|
I agree with Bob. I wouldn't want to have to clear out my last flight.
|
|
MysticCobra
Senior Member Joined: 29 Jan 2013 Status: Offline Points: 652 |
Post Options
Thanks(0)
|
I hardly ever fly the reverse route of what I just flew. It would be an annoyance to not start with a clean flight plan. For commonly-flown routes, I have those saved and can load them when appropriate.
Edited by MysticCobra - 07 Aug 2019 at 11:58am |
|
SB Jim
Senior Member Joined: 30 Aug 2012 Status: Offline Points: 204 |
Post Options
Thanks(0)
|
My 2004 Garmin CNX 80 has started up with whatever flight plan it had active upon shutdown for the past 15 years...... and I *really* liked that feature.
For typical VFR flights it was super easy to reverse the existing plan for the trip back home. Sure, that doesn’t work for IFR. I miss that FEATURE which was a time saver and handy. I understand all the workarounds, I’ve been using my IFD 540 for 4.5 years.....
|
|
Bob H
Senior Member Joined: 26 Jan 2018 Location: NH - KMHT Status: Offline Points: 290 |
Post Options
Thanks(0)
|
For typical VFR flights it was super easy to reverse the
existing plan for the trip back home. Sure, that doesn’t work for IFR. I miss that FEATURE which was a time saver and handy. I understand all the workarounds, I’ve been using my IFD
540 for 4.5 years..... The IFDx40s are arguably the best GA IFR GPS units on the
market. These boxes are intended for IFR
and are at their best during IFR. You
are requesting a VFR function that you agree doesn’t work for IFR. That would be pretty short sighted of Avidyne. Finally, these aren’t workarounds. Workaround implies deficiency. To the contrary, the IFD architecture is intentionally
setup this way because it is the best structure for an IFR GPS. The relationship between FPL and Routes works
extremely well. Edited by Bob H - 07 Aug 2019 at 9:17pm |
|
Bob
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |