![]() |
IFD540 and G 796 (Aeras) |
Post Reply ![]() |
Author | |
oskrypuch ![]() Senior Member ![]() Joined: 09 Nov 2012 Location: CYFD Status: Offline Points: 3058 |
![]() ![]() ![]() ![]() ![]() Posted: 12 Oct 2013 at 7:57pm |
I understand that the IFD540s will not crossfill with the GNS530s, this is not the subject of this question.
The question is -- we have our GNS sending/updating its active flight plan to a dock-mounted Garmin 796. This is a simple serial input produced by the GNS, and input into the 796, using the "aviation in" format I believe. This is a pretty common setup. Is this supported by the IFD540? * Orest Edited by oskrypuch - 12 Oct 2013 at 8:33pm |
|
![]() |
|
AviJake ![]() Admin Group ![]() Joined: 26 Mar 2009 Location: Lincoln MA Status: Offline Points: 2815 |
![]() ![]() ![]() ![]() ![]() |
Yes, that interface is completely supported by the IFD540/440. In fact, I use it every day in the Avidyne test airplane where I have some external devices on the glareshield that take data like flight plan routing in via the Aviation 232 protocol.
As part of the Plug and Play nature of the IFD series of products, we've tried to ensure that every device and protocol that the GNS units supported is also supported by the IFD. HTAWS so far is the only known exception.
|
|
Steve Jacobson
sjacobson@avidyne.com |
|
![]() |
|
oskrypuch ![]() Senior Member ![]() Joined: 09 Nov 2012 Location: CYFD Status: Offline Points: 3058 |
![]() ![]() ![]() ![]() ![]() |
OK, good to hear, I thought I had read about the Aera type units somewhere but could not find that explicitly in the FAQ.
I expect that there is full compatibility with JPI 830 fuel flow & distance to destination type data back/forth on 232 as well, and ASPEN on 429 & 232. * Orest Edited by oskrypuch - 13 Oct 2013 at 11:51am |
|
![]() |
|
AviJake ![]() Admin Group ![]() Joined: 26 Mar 2009 Location: Lincoln MA Status: Offline Points: 2815 |
![]() ![]() ![]() ![]() ![]() |
Yup.
|
|
Steve Jacobson
sjacobson@avidyne.com |
|
![]() |
|
LarryPetro ![]() Groupie ![]() ![]() Joined: 03 Nov 2011 Location: Washington, DC Status: Offline Points: 66 |
![]() ![]() ![]() ![]() ![]() |
And, Insight Avionics GEM G3 fuel flow?
|
|
Larry Petro - Columbia 350 @ KFME
|
|
![]() |
|
oskrypuch ![]() Senior Member ![]() Joined: 09 Nov 2012 Location: CYFD Status: Offline Points: 3058 |
![]() ![]() ![]() ![]() ![]() |
Insight uses the same Shadin format on 232, so it should work as well. (not official answer)
* Orest |
|
![]() |
|
AviJake ![]() Admin Group ![]() Joined: 26 Mar 2009 Location: Lincoln MA Status: Offline Points: 2815 |
![]() ![]() ![]() ![]() ![]() |
Well we're not explicitly calling out support for the Insight GEM G3 since it wasn't explicitly called out by the GNS530. I haven't looked at the G3 Interface Control Document or equivalent so I'm not sure what data it's expecting to send or receive but as Orest notes, those standard 232 protocols are supported by the IFD540.
|
|
Steve Jacobson
sjacobson@avidyne.com |
|
![]() |
|
Leonard ![]() Senior Member ![]() ![]() Joined: 05 Jul 2012 Location: Lafayette LA Status: Offline Points: 107 |
![]() ![]() ![]() ![]() ![]() |
Insight's G3 is working on my G 530.
BTW It was nice to see the 540 in action at AOPA's summit in Ft.Worth
Edited by Leonard - 21 Oct 2013 at 8:54pm |
|
![]() |
|
AviJake ![]() Admin Group ![]() Joined: 26 Mar 2009 Location: Lincoln MA Status: Offline Points: 2815 |
![]() ![]() ![]() ![]() ![]() |
In other words fuel flow from the G3 is showing up on the 530? If so, can you send me a copy of how your 232 Configuration is set up on the 530? I can provide instructions on how to find that if needed.
|
|
Steve Jacobson
sjacobson@avidyne.com |
|
![]() |
|
LarryPetro ![]() Groupie ![]() ![]() Joined: 03 Nov 2011 Location: Washington, DC Status: Offline Points: 66 |
![]() ![]() ![]() ![]() ![]() |
Steve,
I've sent you several relevant Insight Avionics documents via private message. -Larry
|
|
Larry Petro - Columbia 350 @ KFME
|
|
![]() |
|
LarryPetro ![]() Groupie ![]() ![]() Joined: 03 Nov 2011 Location: Washington, DC Status: Offline Points: 66 |
![]() ![]() ![]() ![]() ![]() |
As I understand, RS232, which the G3 and GNS 530W use, is an electrical standard. I wonder whether the data formats supported by each instrument are compatible so that the system does work.
|
|
Larry Petro - Columbia 350 @ KFME
|
|
![]() |
|
LarryPetro ![]() Groupie ![]() ![]() Joined: 03 Nov 2011 Location: Washington, DC Status: Offline Points: 66 |
![]() ![]() ![]() ![]() ![]() |
> Insight's G3 is working on my G 530.
That's good news. If the IFD540 fully implements GNS 530W functions, then I would expect the fuel flow to display on the IFD540 too. I hope Steve can verify that. Thanks.
|
|
Larry Petro - Columbia 350 @ KFME
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |