Codes for ICAO flight plan
Printed From: Avidyne
Category: Avidyne General
Forum Name: IFD 5 Series & IFD 4 Series Touch Screen GPS/NAV/COM
Forum Description: Topics on Avidyne's IFD 5 Series and IFD 4 Series Touch Screen GPS/NAV/COM
URL: http://forums.avidyne.com/forum_posts.asp?TID=1201
Printed Date: 05 May 2024 at 6:17am
Software Version: Web Wiz Forums 12.01 - http://www.webwizforums.com
Topic: Codes for ICAO flight plan
Posted By: N927BC
Subject: Codes for ICAO flight plan
Date Posted: 11 Jan 2017 at 12:24pm
| Does the IFD540 qualify as a FMS in the ICAO flight plan? Do I check the FMS box on the ICAO flight plan form |
Replies:
Posted By: Catani
Date Posted: 11 Jan 2017 at 12:47pm
| The IFD is an FMS. I don't see an FMS box on the ICAO flight plan form. |
Posted By: ansond
Date Posted: 11 Jan 2017 at 4:27pm
|
Looking through the equipment options, I am thinking: SBGLORY Thoughts? Catchy... Doug
|
Posted By: mfb
Date Posted: 11 Jan 2017 at 9:55pm
|
This is how I do it. The screen shots are from DUATS but any flight planning software will be similar.   I have an MLB100, so I have 1090 ADS-B out and UAT ADS-B in. But there's no code for that. So it's indicated by the 260B in the SUR/ field. There was another thread here a long time ago that explained it. All of the other field values are derived from the information in the IFD540 flight manual supplement. The CODE/ field is the hexadecimal address of my transponder. Mike |
Posted By: wsh
Date Posted: 12 Jan 2017 at 1:44am
|
Actually You are missing Y. In europe this is now relevant in many countries. |
Posted By: chflyer
Date Posted: 12 Jan 2017 at 2:58am
|
There was already a long discussion within the last week on this in the Entegra General Information forum. Although the codes might be slightly different depending on the box, I would suggest that the Avidyne moderator merge the two since the discussion is largely overlapping. R and the associated PBN remark is a can of worms and isn't necessary (or used by ATC) in the USA. As far as I know it is only required for IFR flight plans in Europe. It is designed to reflect performance capability/approval and not just installed equipment. I think the PBN list above is too short for a normal IFD installation. I would suggest the following: PBN/A1B2C2D2L1O2S1. That is what is coded by autorouter.eu if the aircraft is configured with an Avidyne IFD box. Yes, Y is needed for Europe due to certain airspace requirements for 8.33kHz. If it is coded then the IFD also needs to have 8.33kHz selected in the SETUP/User Options. Is 8.33kHz used at all in the USA?
------------- Vince |
Posted By: wsh
Date Posted: 12 Jan 2017 at 3:06am
|
I use: SBDFGRY/S and in other information PBN/B2S1 NAV/SBAS I do however have both DME and ADF which are used in Europe.
Many of the other PBN codes require additional equipment which you will typically not find in GA aircraft.
|
Posted By: oskrypuch
Date Posted: 12 Jan 2017 at 7:58am
No, not in US nor Canada. There may be a move to assign 833 spacing for some of the high enroute frequencies, which won't affect small plane GA. I have 833 turned OFF, to speed up tuning. * Orest |
chflyer wrote:Posted By: oskrypuch
Date Posted: 12 Jan 2017 at 8:01am
That is what I came up with a few years ago, reading through the codes. I think that ATC on this side of the Atlantic ignores that string for the most part, so for now it doesn't make a lot of difference what you have. * Orest |
Posted By: Ibraham
Date Posted: 15 Jan 2017 at 2:12pm
|
This is from the Avidyne official tech support portal https://techsupport.avidyne.com/portal/helpcenter/articles/ifd540-ifd440-icao-filing-codes
FD540 / IFD440 ICAO Filing Codes540/440 Equipment Qualifier:
B – LPV L – ILS O – VOR R – PBN Approved S – VHF, VOR, ILS Y – VHF w/8.33 kHz spacing
PBN string:
A1 – RNP10 C2 – RNAV-2 D2 – RNAV-1 L1 – RNP4 S1 – RNP APCH
And if the AXP340 or AXP322 are thrown in, you pick up
Surveillance:
E – Mode S, including aircraft ID, pressure altitude, extended squitter B1 – ADS-B with dedicated 1090 MHz ADS-B Out Capability |
Posted By: chflyer
Date Posted: 15 Jan 2017 at 6:12pm
|
The above list is also in the FAQ, question 6. ------------- Vince |
Posted By: Catani
Date Posted: 15 Jan 2017 at 7:50pm
|
As I understand the codes required by the FAA for US operators (and I’m willing to be
corrected as may be necessary):
Item 10 should include neither L nor O, since S already indicates that capability. The letter G is missing from Item 10, which is required to indicate that the IFD is a GPS capable system. And the letter Z is missing, which is required to indicate that there are “other” entries in Item 18 besides PBN. Missing from Item 18 is NAV/SBAS, indicating that the IFD WAAS capability relies upon a Space Based Augmentation System (as opposed to a ground-based system). It is this entry that requires the letter Z in Item 10. See JO 7110.10Y, Appendix A – ICAO Flight Plans. In my plane, which has an IFD440 and an ADS-B 1090 in and out system, my codes are: Item 10: SBGRYZ/EB2 Item 18: PBN/A1C2D2L1S1 NAV/SBAS SUR/260B CODE/XXXX Not sure why Avidyne does not include B2 in the PBN string, but I’m assuming it’s because C2 (RNP 2) is a stiffer requirement than B2 (RNP 5) capability, and because B2 reflects Europe’s RNP 5 (B-RNAV) standard, which is apparently not used in the US. You could omit the PBN codes A1 and L1 if you don’t fly in oceanic airspace. |