Avidyne Homepage
Forum Home Forum Home > Avidyne General > IFD 5 Series & IFD 4 Series Touch Screen GPS/NAV/COM
  New Posts New Posts RSS Feed - Release 10.2.3.1
  FAQ FAQ  Forum Search   Register Register  Login Login

Release 10.2.3.1

 Post Reply Post Reply Page  <1 234
Author
Message
Stevei View Drop Down
Groupie
Groupie


Joined: 13 Dec 2018
Location: No. California
Status: Offline
Points: 49
Post Options Post Options   Thanks (0) Thanks(0)   Quote Stevei Quote  Post ReplyReply Direct Link To This Post Posted: 24 May 2019 at 8:07pm
I had my update done at a shop, and all my datablock settings were lost. Not that big a deal.
Further, until I was in the air, going home, I didn't realize that "Remote" needed to be changed to "Local" in Config since I got rid of my Stratus and installed a Garmin 345. I'll have to try to do that myself Sunday.
Is there anything else I need to do in Config?

Back to Top
GBSoren71965 View Drop Down
Newbie
Newbie
Avatar

Joined: 25 Feb 2018
Location: MN
Status: Offline
Points: 39
Post Options Post Options   Thanks (0) Thanks(0)   Quote GBSoren71965 Quote  Post ReplyReply Direct Link To This Post Posted: 24 May 2019 at 8:27pm
I did my update myself, with my A&P oversite. Went fine, I'd say it took about 50 min. As far as I can tell no settings were lost. I really appreciate Avidyne making it available so I don't have to bring it in to a dealer!
Back to Top
Catani View Drop Down
Senior Member
Senior Member


Joined: 21 Jan 2016
Status: Offline
Points: 284
Post Options Post Options   Thanks (0) Thanks(0)   Quote Catani Quote  Post ReplyReply Direct Link To This Post Posted: 25 May 2019 at 12:25am
Tried to get 10.2.3.1 done at my local dealer, but they were slammed by ADS-B work and said they could not do it anytime soon.  Glad Avidyne provides the A&P option.  My A&P agreed to sign off on the install so long as it checked out afterwards.  Took less than an hour, no difficulties.  The only user option setting, datablock, configuration, or any other user info lost that I can see is that the wifi password went back to the default.
Back to Top
oskrypuch View Drop Down
Senior Member
Senior Member


Joined: 09 Nov 2012
Location: CYFD
Status: Offline
Points: 2498
Post Options Post Options   Thanks (1) Thanks(1)   Quote oskrypuch Quote  Post ReplyReply Direct Link To This Post Posted: 25 May 2019 at 12:35am
I found the map page datablocks set to default, the wifi setup had to be redone, and all the settings for my remote transponder were nil-ed out.

Simple to set up again, I have pics of all the pages and screens.

* Orest

Back to Top
teeth6 View Drop Down
Senior Member
Senior Member


Joined: 10 Mar 2014
Status: Offline
Points: 540
Post Options Post Options   Thanks (0) Thanks(0)   Quote teeth6 Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2019 at 1:57pm

I must have missed some step in the setup or I'm the problem child again. lol.  To setup "remote" WiFi and use my Stratus, this is what I entered on the config page and what shows on my Aux setup page but the IFD does not connect with the Stratus.   I notice that when I select the IFD  using local WiFi I am asked to hit the allow button but when I select the Stratus as the remote Wifi, no such screen pops up to ask permission.


Edited by teeth6 - 26 May 2019 at 1:57pm
Back to Top
Ibraham View Drop Down
Senior Member
Senior Member


Joined: 21 May 2016
Location: KHWO
Status: Offline
Points: 251
Post Options Post Options   Thanks (0) Thanks(0)   Quote Ibraham Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2019 at 3:06pm
When you select the Stratus on Wi-Fi in the iPad Settings, Is Avidyne showing up in "Devices" in Foreflight (it may take up to a minute to connect)?

I believe the only feature that is available when IFD is connected to the Stratus remote network is flight plan transfer through Foreflight. It will also allow Foreflight to get ADS-B and GPS data from Stratus.


Back to Top
AviSteve View Drop Down
Admin Group
Admin Group
Avatar

Joined: 12 Feb 2018
Location: Melbourne, FL
Status: Offline
Points: 754
Post Options Post Options   Thanks (0) Thanks(0)   Quote AviSteve Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2019 at 6:55pm
Originally posted by teeth6 teeth6 wrote:

... this is what I entered on the config page and what shows on my Aux setup page but the IFD does not connect with the Stratus.   I notice that when I select the IFD  using local WiFi I am asked to hit the allow button but when I select the Stratus as the remote Wifi, no such screen pops up to ask permission.
Make absolutely sure that the SSID is correct in maintenance mode (zero instead of the letter o, no spaces at the end, etc.).  Also make sure password is completely empty.
Steve Lindsley
Avidyne Engineering
Back to Top
teeth6 View Drop Down
Senior Member
Senior Member


Joined: 10 Mar 2014
Status: Offline
Points: 540
Post Options Post Options   Thanks (0) Thanks(0)   Quote teeth6 Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2019 at 6:59pm
Went back to the plane and found my mistake.  I had all the digits correct (using zero instead of letter O) but the one mistake I made was using a "capital" S in Stratus2S instead of Stratus2s as it appeared.  That one mistake made all the difference.  :).   Thank you. 
Back to Top
Catani View Drop Down
Senior Member
Senior Member


Joined: 21 Jan 2016
Status: Offline
Points: 284
Post Options Post Options   Thanks (0) Thanks(0)   Quote Catani Quote  Post ReplyReply Direct Link To This Post Posted: 27 May 2019 at 4:44pm
Steve - I successfully updated my IFD440 with 10.2.3.1., under my A&P's supervision.  Can I get a link to the install manual rev 15 or later so as to accomplish the "System Checkout" procedures listed in Section 4 of the service bulletin?  I can't locate it on the website. Thanks.
Back to Top
HenryM View Drop Down
Senior Member
Senior Member


Joined: 13 Oct 2017
Location: Texas
Status: Offline
Points: 289
Post Options Post Options   Thanks (0) Thanks(0)   Quote HenryM Quote  Post ReplyReply Direct Link To This Post Posted: 27 May 2019 at 5:21pm
I would like a copy of the manual too. One part of the service bulletin says rev 15, but another says rev 17. I believe the latter is the correct one, right?
Back to Top
AviSteve View Drop Down
Admin Group
Admin Group
Avatar

Joined: 12 Feb 2018
Location: Melbourne, FL
Status: Offline
Points: 754
Post Options Post Options   Thanks (1) Thanks(1)   Quote AviSteve Quote  Post ReplyReply Direct Link To This Post Posted: 28 May 2019 at 9:55am
Use the same link that you used to get the software update.  We have posted an updated Service Bulletin (correcting the wrong rev reference), the Install Manual, and Instructions for Continued Airworthiness.
Steve Lindsley
Avidyne Engineering
Back to Top
Catani View Drop Down
Senior Member
Senior Member


Joined: 21 Jan 2016
Status: Offline
Points: 284
Post Options Post Options   Thanks (1) Thanks(1)   Quote Catani Quote  Post ReplyReply Direct Link To This Post Posted: 28 May 2019 at 10:54am
Originally posted by AviSteve AviSteve wrote:

Use the same link that you used to get the software update.  We have posted an updated Service Bulletin (correcting the wrong rev reference), the Install Manual, and Instructions for Continued Airworthiness.

Thanks.  I only downloaded the "full install" folder.  Did not notice the separate manual.  Will do the post-install checkout and get the signed Maintenance Record out to Avidyne today.  Thanks again.
Back to Top
WingNut View Drop Down
Newbie
Newbie


Joined: 22 Oct 2018
Location: Alabama
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote WingNut Quote  Post ReplyReply Direct Link To This Post Posted: 29 May 2019 at 2:07pm
@aviSteve, a little clarification for the wifi changes please.  I've been updated, but the shop did not back up my settings prior to the update so I lost some stuff including my wifi settings.  I have since read one of your responses elsewhere that seems to indicate that I can now have several "local" and several "remote" connections configured in maintenance mode, and the 440 will (apparently) ask me on boot which connection I want to pursue?  If that's how it works, that's a great improvement!

Previously, I just assumed I would lose connectivity to the 440 if the ADS-B IN device went south.  But now apparently I can reboot the 440, select the 440 as "local", and connect the iPad to the 440's wifi signal.

Is this how it works?
Back to Top
scott_757 View Drop Down
Newbie
Newbie


Joined: 06 May 2019
Location: Houston
Status: Offline
Points: 3
Post Options Post Options   Thanks (0) Thanks(0)   Quote scott_757 Quote  Post ReplyReply Direct Link To This Post Posted: 29 May 2019 at 2:19pm
Did the update on my IFD 440 this morning along with my SC and everything completed with no errors but now getting an "ADS-B GPS Position Invalid: ADS-B Traffic Sensor lacks GPS position" error on my IFD.  It's connected to a FreeFlight RANGR and everything worked before the IFD upgrade.  The input/output configs on the IFD match what they were before the upgrade.  Any thoughts on what to check?

Thanks,
Back to Top
AviSteve View Drop Down
Admin Group
Admin Group
Avatar

Joined: 12 Feb 2018
Location: Melbourne, FL
Status: Offline
Points: 754
Post Options Post Options   Thanks (1) Thanks(1)   Quote AviSteve Quote  Post ReplyReply Direct Link To This Post Posted: 29 May 2019 at 3:41pm
Originally posted by WingNut WingNut wrote:

... clarification for the wifi changes ...
You can have up to four configurations that you define in Maintenance mode.  Then you can select from those four in flight mode on the setup page.  It doesn't ask you on startup.  It's all described in the new version of the Pilots Guide (page 7-72 of the 500 series guide, page 6-70 of the 400 series guide).  The pilots guides are downloadable from our website.


Originally posted by WingNut WingNut wrote:

Previously, I just assumed I would lose connectivity to the 440 if the ADS-B IN device went south.  But now apparently I can reboot the 440, select the 440 as "local", and connect the iPad to the 440's wifi signal.
I think you're saying that you typically have the IFD (in remote mode) and and IFD100 connected to something like a Stratus and are wondering what to do if you lose the Stratus.  Assuming I got that right... you don't have to reboot the IFD.  You just have to go to the setup page and choose one of the local configurations that you have defined and then connect the IFD100 to that network.



Steve Lindsley
Avidyne Engineering
Back to Top
allenc3 View Drop Down
Groupie
Groupie
Avatar

Joined: 04 Feb 2019
Location: 32043
Status: Offline
Points: 45
Post Options Post Options   Thanks (0) Thanks(0)   Quote allenc3 Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 1:22am
My problem now is I cannot get the IDE 100 to work in remote mode (worked fine in last revision) I turn on the Stratus box, select Strutus2XXXXX from Ipad mini with foreflight, Type Stratus2XXXXX into the second block on maint mode then select remote.

Then select Stratus2XXXX Remote from user side and finally, Select Stratus2xxxxx from the WIFI section on the IDE 100 App.

Am I correct so far?

When I do this, the Foreflight Mini and the IDF Mini seem to log on but the IDF 100 fails to log on, ie no com or gps data comes across.

What am I doing wrong?

BTW, if logging on direct it logs right on (Local),
Claude
Back to Top
oskrypuch View Drop Down
Senior Member
Senior Member


Joined: 09 Nov 2012
Location: CYFD
Status: Offline
Points: 2498
Post Options Post Options   Thanks (0) Thanks(0)   Quote oskrypuch Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 1:35pm
Be absolutely certain you have the zeros and ohs, and ones and els, all correct. Took me two goes initially.

* Orest

Back to Top
210 Driver View Drop Down
Newbie
Newbie
Avatar

Joined: 28 Jan 2014
Location: Alberta, CAN
Status: Offline
Points: 36
Post Options Post Options   Thanks (0) Thanks(0)   Quote 210 Driver Quote  Post ReplyReply Direct Link To This Post Posted: 06 Jun 2019 at 2:02pm
So I had my update to the latest software (IFD540), and had my old GDL69A activated for a month, but can’t seem to get the WX to show. Is there anyway to update the GDL FIRMWARE so that it will work with my 540? 

My tech read that I must use an old G*530...

If I can’t get it working, may as well tear it out...

Any replies appreciated.
Back to Top
martinrdb View Drop Down
Newbie
Newbie


Joined: 27 Apr 2019
Location: KSUS
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote martinrdb Quote  Post ReplyReply Direct Link To This Post Posted: 06 Jun 2019 at 6:10pm
I have exactly the same problem as you - my IFD 550 is showing "ADS-B GPS Position Invalid: ADS-B Traffic Sensor lacks GPS position" after the 10.2.3.1 upgrade with the FreeFlight Rangr. All the config for the FreeFlight is still ok.
Did you find out what the issue is and any way to correct it ?
Back to Top
Alouicious View Drop Down
Newbie
Newbie
Avatar

Joined: 16 Dec 2015
Location: OR70 and KBOW
Status: Offline
Points: 16
Post Options Post Options   Thanks (0) Thanks(0)   Quote Alouicious Quote  Post ReplyReply Direct Link To This Post Posted: 07 Jun 2019 at 7:18pm
10.2.3.1 updated smoothly on both IFD 540 and IFD 440.  Less than an hour each once started, but a lot more in prep and post.  Some of the new Config pages are different than before (10.2.0.0.A).  My data blocks on the 540's right side had minor differences, and the top of the 440 were changed to the same as the 540.  

Adjusted the lighting configuration per the Manual as mine isn't wired to the panel 'dim bus.'  

Used a 6 amp battery charger connected at the battery, and everything I could turn off was.

Fairly simple:  the Service Bulletin is loaded with how to deal with abnormalities.  Check list beginning on page 11/17 will keep you on track.

The Installation Manual (Rev 17) provided in the 10.2.3.1.zip download is very helpful beginning on page 90... If pressing Enter doesn't work, try pressing the lower right knob.  Sometimes took several tries.

So:  What words are being used to log the update?  The A&P/IA is willing, but wants to just sign the logbook.
Thanks!
Al
Be happy! Your choice.
Back to Top
Alouicious View Drop Down
Newbie
Newbie
Avatar

Joined: 16 Dec 2015
Location: OR70 and KBOW
Status: Offline
Points: 16
Post Options Post Options   Thanks (0) Thanks(0)   Quote Alouicious Quote  Post ReplyReply Direct Link To This Post Posted: 07 Jun 2019 at 8:53pm
How about this:
IFD 540 and IFD 440 updated to 10.2.3.1 i.a.w. Avidyne S.B. 601-00182-034.

You're welcome.
Be happy! Your choice.
Back to Top
teeth6 View Drop Down
Senior Member
Senior Member


Joined: 10 Mar 2014
Status: Offline
Points: 540
Post Options Post Options   Thanks (0) Thanks(0)   Quote teeth6 Quote  Post ReplyReply Direct Link To This Post Posted: 07 Jun 2019 at 9:12pm
You should also include the SNs of the boxes updated.
Back to Top
donemory View Drop Down
Newbie
Newbie
Avatar

Joined: 18 Feb 2019
Location: Medina, OH
Status: Offline
Points: 26
Post Options Post Options   Thanks (0) Thanks(0)   Quote donemory Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jun 2019 at 1:24pm
Since doing the 10.2.3.1 update, every time I power on my IFD540, (others say their IFD440 does the same), it displays the bottom end of my data blocks and I have to scroll back to the top. Has any one else had this issue and is there a way to correct it so that it displays the top end of the data blocks?  Avidyne any fix here?
Don
Back to Top
ttvetdoc View Drop Down
Newbie
Newbie


Joined: 23 Mar 2018
Status: Offline
Points: 14
Post Options Post Options   Thanks (0) Thanks(0)   Quote ttvetdoc Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jun 2019 at 1:49pm
Originally posted by donemory donemory wrote:

Since doing the 10.2.3.1 update, every time I power on my IFD540, (others say their IFD440 does the same), it displays the bottom end of my data blocks and I have to scroll back to the top. Has any one else had this issue and is there a way to correct it so that it displays the top end of the data blocks?  Avidyne any fix here?

I have noticed the exact same issue on mine since the update.  A minor issue but certainly a little frustrating as I use the datablocks on every flight, especially for IFR flying.
SR22 - KEQY
Back to Top
Catani View Drop Down
Senior Member
Senior Member


Joined: 21 Jan 2016
Status: Offline
Points: 284
Post Options Post Options   Thanks (0) Thanks(0)   Quote Catani Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jun 2019 at 2:32pm
I get that datablock scroll issue as well.  Was thinking of filling up all the data blocks with something to see what happens.
Back to Top
n7ifr View Drop Down
Senior Member
Senior Member
Avatar

Joined: 05 Aug 2013
Location: Scottsdale, Az
Status: Offline
Points: 389
Post Options Post Options   Thanks (0) Thanks(0)   Quote n7ifr Quote  Post ReplyReply Direct Link To This Post Posted: 14 Jun 2019 at 6:47pm
Same issue here... 
Not too inconvenient though, just a flick of the finger to scroll back up.

Tom W.
Back to Top
Ralph View Drop Down
Newbie
Newbie


Joined: 16 Jun 2019
Location: Newport, OR
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote Ralph Quote  Post ReplyReply Direct Link To This Post Posted: 18 Jun 2019 at 8:58pm
Did anyone notice the COM PRESET not working from the blue tooth keyboard after the upgrade?  I also noted that I couldn't change NAV frequencies on the iPad.  Avidyne acknowledges the latter but I didn't get a solid answer on the blue tooth keyboard issue.  Everything else on the blue tooth appears to function normally.
Back to Top
DH82FLYER View Drop Down
Groupie
Groupie


Joined: 15 Dec 2012
Location: Queensland
Status: Offline
Points: 59
Post Options Post Options   Thanks (0) Thanks(0)   Quote DH82FLYER Quote  Post ReplyReply Direct Link To This Post Posted: 18 Jun 2019 at 11:04pm
Yes, agree the COM PRESET is now not working on the Bluetooth keyboard. 

Thomas


Edited by DH82FLYER - 18 Jun 2019 at 11:07pm
Back to Top
oskrypuch View Drop Down
Senior Member
Senior Member


Joined: 09 Nov 2012
Location: CYFD
Status: Offline
Points: 2498
Post Options Post Options   Thanks (0) Thanks(0)   Quote oskrypuch Quote  Post ReplyReply Direct Link To This Post Posted: Yesterday at 9:30am
Originally posted by DH82FLYER DH82FLYER wrote:

Yes, agree the COM PRESET is now not working on the Bluetooth keyboard.


That would be too bad, it is a very handy feature when on a local/common flight. Happily I have a toggle on my yoke to achieve that, and use it all the time.

* Orest
Back to Top
AviSteve View Drop Down
Admin Group
Admin Group
Avatar

Joined: 12 Feb 2018
Location: Melbourne, FL
Status: Offline
Points: 754
Post Options Post Options   Thanks (0) Thanks(0)   Quote AviSteve Quote  Post ReplyReply Direct Link To This Post Posted: Yesterday at 11:25am
Originally posted by Ralph Ralph wrote:

Did anyone notice the COM PRESET not working from the blue tooth keyboard after the upgrade?  I also noted that I couldn't change NAV frequencies on the iPad.  Avidyne acknowledges the latter but I didn't get a solid answer on the blue tooth keyboard issue.  Everything else on the blue tooth appears to function normally.
Confirmed.  Sorry that one slipped through the cracks.  We have a fix for the next release, but I realize that will be a while.
Steve Lindsley
Avidyne Engineering
Back to Top
HenryM View Drop Down
Senior Member
Senior Member


Joined: 13 Oct 2017
Location: Texas
Status: Offline
Points: 289
Post Options Post Options   Thanks (0) Thanks(0)   Quote HenryM Quote  Post ReplyReply Direct Link To This Post Posted: Yesterday at 2:15pm
Next release of the IFD100? No changes to the panel-mount IFD?

Out of curiosity, is releasing an app update for the IFD100 a big deal from a certification point of view, or is it like any other iOS app?
Back to Top
AviSteve View Drop Down
Admin Group
Admin Group
Avatar

Joined: 12 Feb 2018
Location: Melbourne, FL
Status: Offline
Points: 754
Post Options Post Options   Thanks (0) Thanks(0)   Quote AviSteve Quote  Post ReplyReply Direct Link To This Post Posted: Yesterday at 2:34pm
Sorry, no it's in the IFD software, not just IFD100.

IFD100 is like any other iPad app.  We don't publish a new version for every little change though.
Steve Lindsley
Avidyne Engineering
Back to Top
HenryM View Drop Down
Senior Member
Senior Member


Joined: 13 Oct 2017
Location: Texas
Status: Offline
Points: 289
Post Options Post Options   Thanks (0) Thanks(0)   Quote HenryM Quote  Post ReplyReply Direct Link To This Post Posted: Yesterday at 4:08pm
Thanks for the explanation, Steve.
Back to Top
 Post Reply Post Reply Page  <1 234
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.070 seconds.